My First Quilt: Part 2

Hello all! I know, it has been ages since the last update on this project, like on so many projects actually ;). To recap: I am talking about this quilt:

DSCN4142.jpg

Last week, I decided to continue working on it. I have lots of now projects coming up, so better finish this one first! The last time I worked on it was before the final stage of my study, which was somewhere in july I think. I already bought all the stuff I needed, so the only thing I had to do now was putting everything together. So I gathered all the pieces and continued!

My last post on this quilt (part 1) ended with a finished top layer. So let’s continue with the back of this quilt!

STEP 8

I decided to include a pieced strip in the back, because this will break up the otherwise solid chocolate-brown fabric of the back. For this, I needed 26 rectangular pieces of fabric, 15 cm long and 7,5 cm wide. The first four pieces were provided by the leftover block from the quilt top. Bust out the seams and cut the square in half, and you already have 4 strips! The rest is cut from the rectangles you cut in the beginning. Don’t cut all of them to pieces, you are gonna need some of them for the border around your quilt later on! Therefore, keep track of how much you’ve cut. Then, sew them all together along the long edges into a strip like this:

DSCN4258press all the seams the same way and put this strip aside for later.

STEP 9

Take the fabric for your back and make sure it’s absolutely flat. Cut of the selfedges and make sure the cutting edge of the fabric is straight and perpendicular to the selfedges. Now, sew one side of the pieced strip to one of the selfedges, and the other side of the pieced strip to the other selfedge. In case it’s not clear: you are making a tube! Press the seams towards the back fabric. Now, determine how far from the edge you want the pieced strip to be. Fold the tube on that line and pin it to your ironing board, like shown in the picture. If your ironing board is not long enough, no worries! You can shift the whole thing later on.

DSCN4264After you’ve measured and pinned your tube along the length of your ironing board, press the fold very thoroughly. Remove the pins (careful, they are HOT!), shift the tube a bit and repeat the process until you pressed the fold along the whole length of the pieced strip.

STEP 10

Now move your pressed tube to your cutting mat and grab your rotary knife and ruler. Cut of a tiny strip from the pressed edge, only a millimeter or so! This will transform the tube into your quilt back, with the pieced strip somewhere incorporated. Cool, right?

STEP 11

The time has come to put everything together into a quilt sandwich! Make sure you have enough room on the floor to spread your quilt, with some room all around for walking and pinning later on. You want to avoid climbing onto your quilt as much as possible, because this can shift around the layers and that’s something you don’t want to happen! First, spread your quilt back on the floor (face down) and make sure no folds are present. My carpet is like velcro, so it stayed flat by itself, but if your floor is very slippery you might want to tape it down with painter’s tape along the sides to keep everything in place. Then spread your batting over the back. Spread it as flat as possible and flatten out any folds. Then, put your quilt front on top, leaving about 3 cm of back and batting on the edges (this will allow for some possible stretching during the quilting later on). Again, try to put it down as flat as possible, but don’t disrupt the layers underneath! After several atempts I figured rolling up your quilt top and unrolling it on top of the sandwich was the best way, because you can control things much easier. The whole thing should now look like this:

DSCN4266

STEP 12

The next step is basting your quilt. Some people prefer real basting (as in: with needle and thread) but the tutorial I followed used a lot of safety pins, so I decided to try that too. First pin the corner of your quilt and from there, put a safety pin every 10-15cm in a square pattern. Just a little reminder: don’t put pins where you want to quilt. If you plan to sew along the seams, don’t put pins there or you’ll be annoyed all the time later on because you have to remove safety pins all the time. Just a thing to keep in mind! The picture is not very clear, bu this is my quilt somewhere half-way the process:

DSCN4267

Search for the pins ;). After basting your whole quilt, cut the remaining back and batting away (remembering those 3cm around). Now it’s time for quilting! I myself was a bit scared, so I put the quilt away for now, but it’s staring very angrily at me all the time… I guess I can’t run away from it forever!

Advertisements
Categories: General, Home Decoration, Tutorials | Tags: , , , , , , | Leave a comment

Post navigation

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

Create a free website or blog at WordPress.com.

%d bloggers like this: